Roadway equipment used to detect vehicle volumes and/or speeds. Includes equipment such as video image vehicle detection systems (VIVDS), remote traffic microwave sensors (RTMS), or traditional loops. Also includes sensors to detect train lengths and speeds to estimate the anticipated duration of closures.
| Functional Object | Description | User Defined |
|---|
| Roadway Basic Surveillance | 'Roadway Basic Surveillance' monitors traffic conditions using fixed equipment such as loop detectors and CCTV cameras. | False |
|---|
| Roadway Dynamic Lane Management and Shoulder Use | 'Roadway Dynamic Lane Management and Shoulder Use' includes the field equipment, physical overhead lane signs and associated control electronics that are used to manage and control specific lanes and/or the shoulders. This equipment can be centrally controlled by a Traffic Management Center or it can be autonomous and monitor traffic conditions and demand along the roadway and determine how to change the lane controls to respond to current conditions. Lane controls can be used to change the lane configuration of the roadway, reconfigure intersections and/or interchanges, allow use of shoulders as temporary travel lanes, designate lanes for use by special vehicles only, such as buses, high occupancy vehicles (HOVs), vehicles attending a special event, etc. and/or prohibit or restrict types of vehicles from using particular lanes. Guidance and information for drivers can be posted on dynamic message signs. | False |
|---|
| Roadway Environmental Monitoring | 'Roadway Environmental Monitoring' measures environmental conditions and communicates the collected information back to a center where it can be monitored and analyzed or to other field devices to support communications to vehicles. A broad array of weather and road surface information may be collected. Weather conditions that may be measured include temperature, wind, humidity, precipitation, and visibility. Surface and sub–surface sensors can measure road surface temperature, moisture, icing, salinity, and other metrics. | False |
|---|
| Roadway Passive Monitoring | 'Roadway Passive Monitoring' monitors passing vehicles for a signature that can be used to recognize the same vehicle at different points in the network and measure travel times. Depending on the implementation and the penetration rate of the technology that is monitored, other point traffic measures may also be inferred by monitoring the number of vehicles within range over time. Today this approach is implemented most commonly using a Bluetooth receiver that passively monitors Bluetooth devices on–board passing vehicles and license plate readers that record the vehicle license plate number, but any widely deployed vehicle communications technology or feature that can be passively monitored to uniquely identify a vehicle could be used. | False |
|---|
| Roadway Speed Monitoring and Warning | 'Roadway Speed Monitoring and Warning' includes the field elements that monitor vehicle speeds. If the speed is determined to be excessive, an advisory or warning is displayed. Current environmental conditions and other factors that may reduce safe operating speeds may also be taken into account. The operational status (state of the device, configuration, and fault data) is provided to the center. This application can also provide an enforcement function, reporting speed violations to an enforcement agency. | False |
|---|
| Roadway Standard Rail Crossing | 'Roadway Standard Rail Crossing' manages highway traffic at highway–rail intersections (HRIs) where operational requirements do not dictate advanced features (e.g., where rail operational speeds are less than 80 miles per hour). Either passive (e.g., the crossbuck sign) or active warning systems (e.g., flashing lights and gates) are supported depending on the specific requirements for each intersection. These traditional HRI warning systems may also be augmented with other standard traffic management devices. The warning systems are activated on notification of an approaching train by interfaced wayside equipment. The equipment at the HRI may also be interconnected with adjacent signalized intersections so that local control can be adapted to highway–rail intersection activities. Health monitoring of the HRI equipment and interfaces is performed; detected abnormalities are reported through interfaces to the wayside interface equipment and the Traffic Management Center. | False |
|---|
| Roadway Traffic Gap Assist | 'Roadway Traffic Gap Assist' measures the headway to the next approaching vehicle. Based on programmed thresholds, unsafe gaps are identified and reported via roadside signs. Traffic gaps and associated advisories and warnings are also provided to the RSE for communication to connected vehicles. | False |
|---|
| Roadway Traffic Information Dissemination | 'Roadway Traffic Information Dissemination' includes field elements that provide information to drivers, including dynamic message signs and highway advisory radios. | False |
|---|
| Roadway Variable Speed Limits | 'Roadway Variable Speed Limits' includes the field equipment, physical overhead lane signs and associated control electronics that are used to manage and control variable speed limits systems. This equipment monitors traffic and environmental conditions along the roadway. The system can be centrally monitored and controlled by a Traffic Management Center or it can be autonomous, calculating and setting suitable speed limits, usually by lane. This application displays the speed limits and additional information such as basic safety rules and current traffic information to drivers. | False |
|---|
| Document Number | Title | Description |
|---|
| ITE ATC 5201 | Advanced Transportation Controller | This standard defines the functionality and performance requirements for a modern ITS controller known as an ATC. It is similar to the NEMA TS–2 standard in that it defines basic capabilities but leaves hardware choices up to the manufacturer. |
|---|
| ITE ATC 5202 | Model 2070 Controller Standard | This standard specifies the hardware for a modern, open–architecture controller for ITS applications that can run Linux and is capable of executing advanced signal controller logic, among other things. |
|---|
| ITE ATC 5301 | Intelligent Transportation System Standard Specification for Roadside Cabinets | This standard specifies the characteristics of a modern controller cabinet for the ITS industry. |
|---|
| ITE ATC 5401 | Application Programming Interface Standard for the Advanced Transportation Controller | This standard defines the application programmers' interface (API) that should be supported by an ATC, which is an open–architecture controller that can host multiple ITS applications. |
|---|
| NEMA TS 8 | Cyber and Physical Security for Intelligent Transportation Systems | This specification describes how agencies and other transportation infrastructure owner/operators should implement cyber– and physical–security for ITS. |
|---|
| NEMA TS2 | Traffic Controller Assemblies with NTCIP Requirements | This specification covers traffic signaling equipment used to facilitate and expedite the safe movement of pedestrians and vehicular traffic. |
|---|
| NEMA TS4 | Hardware Standards for Dynamic Message Signs (DMS) With NTCIP Requirements | This standard provides hardware specifications for safe, dependable, functional, and easily maintained Dynamic Message Sign (DMS) equipment. |
|---|